Tuesday, March 13, 2012

Build Your Own Gold Rocker Box Or Gold Cradle

First developed in the goldfields of the state of Georgia, the rocker was an important gold mining tool. At the very dawn of the Gold rush to California, the rocker box also known as a cradle was perhaps the most used piece of gold prospecting equipment. For a time it was perhaps even more important that the gold pan. Mostly this was because the miner could make a rocker for himself in the field from rough sawn lumber cut in the forest. They are also truly portable. Rocker boxes were also popular while the Klondike gold rush for working the hillside placers that were far above the creeks.

The 'rocker' is a box with a hopper about 3 to 4 ft. Long and 1 to 2 ft. Wide, sloped like a cradle, and is mounted on semicircular pieces of wood and worked by a, deal with to give it a side motion; and it is also inclined so as to carry the material down to the lower end, which is open. At the upper end is a small hopper that may be removed and which has a sheet-iron bottom perforated with 1/2 -in. Holes. Under the hopper is a canvas apron or tray inclined toward the head of the box but touching neither end of the hopper-box. Some wooden riffles are settled across the box. The material is fed into the hopper and screened straight through by water poured on top; the lighter material is carried over the end, while the riffles in the box catch the gold and magnetic sand. This integrate is cleaned out and panned at the end of the operation. The rocker is used for the same type of work as the gold pan in that it is in general a prospecting tool. A man is able to wash 3 to 5 times more yardage than with the gold pan, and the use of the rocker eliminates much of the backbreaking strain of continuous panning. On the other hand, the easy mobility of the pan as a prospecting gadget is lost.

Aluminum Sheet Pan

So why might a contemporary prospector be concerned in construction his own rocker box? The principal use of a gold rocker is for mining small deposits where water is scarce. It is not truly a desert gadget and it does use some principal water, but not nearly as much as a sluice. In a rocker, gravel requires about three times its own weight of water to wash it. So perhaps the best use is in streams and waterways with very miniature water - where some water is present, but not sufficient to run a sluice box. If sufficient flowing water to run a sluice is present, a sluice is faster and easier to run than a rocker. The rocker is only a primitive machine, having a capacity but one-fifth as great as that of the sluice box, but because it is cheap, requires but miniature water, and saves a high ration of coarse gold, the rocker will continue to be used in many districts.

Build Your Own Gold Rocker Box Or Gold Cradle

The doing of a rocker consists of shoveling gravel onto a screen or grizzly, pouring water over it from a dipper, and at the same time giving the gadget a back-and-forth rocking motion. The grizzly retains all the oversized stones, which are removed by hand when they have been washed clean. The operator briefly examines the oversize rock to be sure no large nuggets or gold specimens are being tossed out. The cradle must be settled on an inclination while being worked, and under the influence of the continued side-to-side rocking the dirt is fast disintegrated, passes down straight through the hopper grizzly and the water and the undersize fall down onto the canvas apron which saves most of the gold and places the remainder at the head end of the trough. From the apron it is conveyed to the inner end of the cradle floor (the sluice box like section of the rocker), from which it flows over the riffles, or bars, and out at the mouth. Riffles, canvas, blankets, corduroy, burlap, or cocoa matting with expanded metal have been used to cover the bottom of the trough and all have met with varying degrees of success in salvage the gold. The compound of cocoa matting covered with expanded metal lath has proven to be quite efficient for most gravels. The frequency of cleaning up depends on the richness and character of the gravel, but clean-ups are usually principal two or three times a day. The hopper is taken off first, then the apron is slid out, and washed in a bucket or tub containing clean water, and finally the gold is collected with a spoon from behind the riffle bars, and panned out.

The rocking request for retrial used should be sufficient to keep the gravel disturbed, allowing the gold to conclude out, but a too vigorous movement will cause a gold loss. The gravel bed should be shifted slightly with each request for retrial and should be evenly distributed across the trough. Generally speaking, the rocker is not known for its quality to save fine gold, but with particular and specialist manipulation, decent fine gold recoveries can be achieved. Tailings from both rockers and sluice boxes should be occasionally panned to check for gold losses. When gold is found near the lower end of the rocker or sluice box, the inherent for losses should be investigated.

Because there is no one "right" build for a rocker box, I am not truly presenting definite plans, but on my website I am giving you the information you need to plan, build and build your own rocker box if that's what you conclude to do. My recommended build for a rocker is to start buy construction a sluice box 40 inches long, 16 inches wide on the bottom, sloped like a cradle, and with rockers at each end. The hopper would be 16 inches quadrate and 6 inches deep, with a sheet metal bottom made of perforated steel with 1/2-inch holes. This hopper box needs to be designed so it can be removed for clean up. A light canvas-covered frame is stretched under the hopper, forming a riffle. quadrate riffles of wood or steel are settled across the bottom of the sluice part of the rocker. Curved feet are settled underneath the sluice part of the box to allow it to be rocked back and forth. Historically, rockers are built of wood, as the early prospectors built them. However, there is no speculate that a rocker could not be built from sturdy heavy gauge sheet aluminum. It would be much lighter that the wood version. Remember that wood also absorbs water, and water logged wood is much heavier than dry wood.

Build Your Own Gold Rocker Box Or Gold Cradle

Gold Prospecting equipment - Should You Build Or Buy?

Last summer, for the very first time, a friend and I industrialized a passion for gold prospecting. But it wasn't just the finding of the gold that we loved, it was more the comprehension of the methods used in finding it, of the engineering of how pans and sluice boxes work. We chose to build our own equipment (for the most part), veering away from the spendy stuff found online. Don't get me wrong. I'm sure that stuff works great. But we wanted the excitement of doing it all ourselves. So how did we build our own gold prospecting equipment? It was simple.

The two most common pieces of equipment in gold prospecting are the gold pan, and the sluice box. Your midpoint gold pan is very cheap, usually about . Black plastic is what I prefer. The gold shows up perfectly against the black. Sluice boxes, on the other hand, can get a bit pricey. Building a sluice is of course a lot simpler than it sounds. Using pieces of plastic cut into uncomplicated geometric shapes (squares and rectangles) we build a very lightweight sluice box from plastic naturally by gluing the pieces together with plastic cement and waiting 24 hours. For plans on Building your own sluice box, one naturally has to type in "sluice box plans" into google and they'll find dozens of step by step instructions on how to build their very own gold catching contraption. A sluice box has a very uncomplicated design. It's just a box, after all. Who can't build a box? A lot of outfitters will try and sell you on lightweight, costly aluminum, wanting top dollar for a uncomplicated sluice box. I say why pay the money when you can of course build a sluice with common materials.

Aluminum Sheet Pan

But back to the sluice box for a moment. Lightweight plastic is easy to work with. As long as one doesn't buy sheets more than a quarter inch thick, it can be reasonably cut with an exacto blade. Add to that the cost of a bottle of plastic cement and you'll have your very own sluice box in a matter of a few hours and anything other pieces of gold prospecting equipment you'll need.

Gold Prospecting equipment - Should You Build Or Buy?

The only thing left to do is find a river that has a reasonable amount of gold still hiding away. In California, that's pretty easy to do. Gold infested rivers are scattered all throughout southern and northern California. Different places have Different levels of gold, but I'm assuming that those reading this already have a spot picked out.

Gold Prospecting equipment - Should You Build Or Buy?